Just How to Remove as Well as Replace a Tub
Just How to Remove as Well as Replace a Tub
Blog Article
We've stumbled on this great article relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and figured it made sense to share it with you here.
Mounting a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately tough job. If the old bathtub is easily accessible, the task can relocate easily; if you need to open up a wall surface to eliminate the old tub as well as position the new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed task, it is much better to think about employing one before you begin. Opportunities are you may need a professional plumber to make tube links.
This post will help you mount a brand-new bathtub in your washroom if you have actually already gotten a new tub as well as don't require to alter the setup of your previous water pipes.
Your devices and also material checklist need to make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, switch on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in area between the faucet and the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former type should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Tub
Utilizing both wooden boards under its feet, position the bathtub in the required placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water and also check all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bath tub must wait till the tub has been used at least once as this will certainly resolve it right into its last setting.
Getting ready for the Setup
Firstly, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a rigid seal, causing the water to pass through the wall in between the bath and also the tiling, leading to issues with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can break relatively very early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I am very involved in Tools You Need to Install a New Bathtub and I really hope you liked the new piece. Those who enjoyed our page plz remember to pass it around. I love reading our article about Installing A Bathtub.
See Availability
Report this page